-> Hier kostenlos registrieren
Oh
this was a mistake
ignore it
this was a mistake
ignore it
Zuletzt bearbeitet:
Elau pacdrive system
- Ersteller Badil
- Erstellt am
-> Hier kostenlos registrieren
- Beiträge
- 21.842
- Reaktionspunkte
- 7.254
-> Hier kostenlos registrieren
Do you have the installation CD or just a download of the software?
I saw contents of CD, there is a EvaluationKit folder there like your image page, I tried to re-install the software from the same page by executing the setup.exe, No choise of installing exaamples during the installation. I think the Autorun install them automatically. Here is the list of *.pro projects in my Examples directory:
Ampel_D_EPAS-4_MAX4_V1640
EndlessFeed2_Example
OPC
UserMan_Project_1
UserMan_Project_1_CallStack
UserMan_Project_1_IEC-Task_Measurement
UserMan_Project_1_Step1
UserMan_Project_1_Step2
There are no EvaluationBord or Kit in my installation directory.
Do you know how can I add it?
Or can you send it to me via email?
The address is "servopackcenter@gmail.com"
Ampel_D_EPAS-4_MAX4_V1640
EndlessFeed2_Example
OPC
UserMan_Project_1
UserMan_Project_1_CallStack
UserMan_Project_1_IEC-Task_Measurement
UserMan_Project_1_Step1
UserMan_Project_1_Step2
There are no EvaluationBord or Kit in my installation directory.
Do you know how can I add it?
Or can you send it to me via email?
The address is "servopackcenter@gmail.com"
- Beiträge
- 21.842
- Reaktionspunkte
- 7.254
-> Hier kostenlos registrieren
Copy the folder to your PC and open the xx.PRO project using EPAS.
Dear DeltaMikeAir
I tried to go advance with your tip. Ther was only one *.pro in the EvaluationKit folder; The name was "VarioCamEval005_w.pro" and fortunately EvaluationKit (PRG) is in there. I opened it by EPAS-4 and every time I try to go online there are some 3700 errors, like this one: Error 3700: CSpline (1): A POU with name 'CSpline is already in library 'CSpline_V000701.lib', all errors are of this kind just by differnt name. The online help of EPAS-4 says you must change the POU name and I tried it, but couldn't manage it. Is there any way to remove this error or other tip to enable controller?
Regards.
I tried to go advance with your tip. Ther was only one *.pro in the EvaluationKit folder; The name was "VarioCamEval005_w.pro" and fortunately EvaluationKit (PRG) is in there. I opened it by EPAS-4 and every time I try to go online there are some 3700 errors, like this one: Error 3700: CSpline (1): A POU with name 'CSpline is already in library 'CSpline_V000701.lib', all errors are of this kind just by differnt name. The online help of EPAS-4 says you must change the POU name and I tried it, but couldn't manage it. Is there any way to remove this error or other tip to enable controller?
Regards.
- Beiträge
- 21.842
- Reaktionspunkte
- 7.254
Where to download them?
-> Hier kostenlos registrieren
From Mediafire I think, The download link was in a forum can't find it now.
- Beiträge
- 21.842
- Reaktionspunkte
- 7.254
I was faced with the same problems as you and was able to solve them relatively quickly using
the manual and online help. Even without experience with these devices. Therefore, my advice
is to either get more involved with the device / manual / help or ask someone with knowledge to write a small project.
I can do that in principle, but it takes 2-3 hours and that is not my job.
the manual and online help. Even without experience with these devices. Therefore, my advice
is to either get more involved with the device / manual / help or ask someone with knowledge to write a small project.
I can do that in principle, but it takes 2-3 hours and that is not my job.
Zuletzt bearbeitet:
- Beiträge
- 21.842
- Reaktionspunkte
- 7.254
-> Hier kostenlos registrieren
No, Sorry.
I write these programs on behalf of clients and it would be an effort for me to adapt this for you. And without customization I can't send it.
Dear DeltaMikeAir
Thanks again for your kindness to my last posts and of course your modesty for corresponding in English wit me.
As you know ELAU SM servo motors utilize SICK STEGMANN encoders, some of them SRS50 type encoders and some other SRS50 type encoders. My SM motor had a defective SRM50 and I bought a new one from SICK. I thought new encoders are always data-free and need to be programmed according to defective one (assuming that the defective one is not broken). I have PGT-11 programming tool of SICK for programming such SRM50 encoders (via SOPAS ET software), and more I tried to program the new one, more I disappointed, because the HEX file of the new one never match the old one, and doesn't recognize in SERCOS topology (along with C400 controller and MC-4). (The topology is complete because other ELAU SM motors recognizable.) Any idea?
Regards
Badil
P.S. In programming the new encoders, I export the *.sdv file from old encoder and then importing it to the new one.
Thanks again for your kindness to my last posts and of course your modesty for corresponding in English wit me.
As you know ELAU SM servo motors utilize SICK STEGMANN encoders, some of them SRS50 type encoders and some other SRS50 type encoders. My SM motor had a defective SRM50 and I bought a new one from SICK. I thought new encoders are always data-free and need to be programmed according to defective one (assuming that the defective one is not broken). I have PGT-11 programming tool of SICK for programming such SRM50 encoders (via SOPAS ET software), and more I tried to program the new one, more I disappointed, because the HEX file of the new one never match the old one, and doesn't recognize in SERCOS topology (along with C400 controller and MC-4). (The topology is complete because other ELAU SM motors recognizable.) Any idea?
Regards
Badil
P.S. In programming the new encoders, I export the *.sdv file from old encoder and then importing it to the new one.
